workgroup:connectors:start
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Last revision Both sides next revision | ||
|
workgroup:connectors:start [2015/12/18 13:35] Lorenz Meier created |
workgroup:connectors:start [2020/04/20 23:43] Hamish Willee Fix up broken link to standards home page. |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Dronecode Autopilot Connector Standard ====== | ||
| - | This document describes the connector series and pinouts Dronecode has standardized. The long-term goal is to offer several tiers of connectors: | ||
| - | * Miniature, in-vehicle: JST GH | + | ====== Pixhawk Autopilot Connector Standard ====== |
| - | * Small, IP9X or similar, automotive grade and sealed: This has not entered the standardization process. | + | |
| - | ===== Dronecode Mini ===== | + | The Pixhawk Autopilot Connector Standard is documented as part of the [[https://pixhawk.org/pixhawk-connector-standard|Pixhawk Reference Standards]] (on Pixhawk.org). |
| - | The Dronecode Mini (DCM) connector standard is intended for in-vehicle, cross-PCB use. It uses the JST GH series which offers a latch lock mechanism at small size and a very competitive cost ($0.15 / 6 pos connector footprint in quantities). | + | > Note, this was originally referred to as the "Dronecode Autopilot Connector Standard". |
| - | ==== Pinouts ==== | ||
| - | === Telemetry Port === | ||
| - | |||
| - | This pinout should be used for any serial port. Ports not supporting hardware flow control should leave the CTS and RTS lines floating. | ||
| - | |||
| - | ^ Pin ^ Signal ^ Volt ^ | ||
| - | | 1 (red) | VCC | +5V | | ||
| - | | 2 (blk) | TX (OUT) | +3.3V | | ||
| - | | 3 (blk) | RX (IN) | +3.3V | | ||
| - | | 4 (blk) | CTS (IN) | +3.3V | | ||
| - | | 5 (blk) | RTS (OUT) | +3.3V | | ||
| - | | 6 (blk) | GND | GND | | ||
| - | |||
| - | === GPS port === | ||
| - | |||
| - | This port is intended for combined serial plus I2C GPS units. | ||
| - | |||
| - | ^ Pin ^ Signal ^ Volt ^ | ||
| - | | 1 (red) | VCC | +5V | | ||
| - | | 2 (blk) | TX (OUT) | +3.3V | | ||
| - | | 3 (blk) | RX (IN) | +3.3V | | ||
| - | | 4 (blk) | I2C1 SCL | +3.3V | | ||
| - | | 5 (blk) | I2C1 SDA | +3.3V | | ||
| - | | 6 (blk) | GND | GND | | ||
| - | |||
| - | |||
| - | === CAN === | ||
| - | |||
| - | ^ Pin ^ Signal ^ Volt ^ | ||
| - | | 1 (red) | VCC | +5V | | ||
| - | | 2 (blk) | CAN_H | +12V | | ||
| - | | 3 (blk) | CAN_L | +12V | | ||
| - | | 4 (blk) | GND | GND | | ||
| - | |||
| - | === ANALOG POWER === | ||
| - | |||
| - | The CURRENT signal should carry an analog voltage from 0-3.3V for 0-60A as default. For high-power units the range should be 0-3.3V for 0-120A. The VOLTAGE signal should carry an analog voltage from 0-3.3V for 0-50V as default. | ||
| - | |||
| - | The VCC lines have to offer at least 2.5A continuous and should default to 5.3V. A lower voltage of 5V is still acceptable, but discouraged. | ||
| - | |||
| - | ^ Pin ^ Signal ^ Volt ^ | ||
| - | | 1 (red) | VCC | +5.3V | | ||
| - | | 2 (blk) | VCC | +5.3V | | ||
| - | | 3 (blk) | CURRENT | +3.3V | | ||
| - | | 4 (blk) | VOLTAGE | +3.3V | | ||
| - | | 5 (blk) | GND | GND | | ||
| - | | 6 (blk) | GND | GND | | ||
| - | |||
| - | ===== Dronecode Debug ===== | ||
| - | |||
| - | To facilitate debug and service cables, Dronecode has developed several debug connectors, of which the Dronecode mini debug connector has entered active service. | ||
| - | |||
| - | ==== DCD-Mini ==== | ||
| - | |||
| - | Dronecode debug port (JST SM06B connector). The indicated voltage is nominal 3.3V, but for a target running at a lower voltage (e.g. 1.8V) the debug probe should shift its voltage to the target sense voltage. Up to 100 mA should be provided on ''VCC TARGET SHIFT'' so that debug adapters can drive their shifter / optocoupler directly from this line. | ||
| - | |||
| - | ^ Pin ^ Signal ^ Volt ^ | ||
| - | | 1 (red) | VCC TARGET SHIFT | +3.3V | | ||
| - | | 2 (blk) | CONSOLE TX (OUT) | +3.3V | | ||
| - | | 3 (blk) | CONSOLE RX (IN) | +3.3V | | ||
| - | | 4 (blk) | SWDIO | +3.3V | | ||
| - | | 5 (blk) | SWCLK | +3.3V | | ||
| - | | 6 (blk) | GND | GND | | ||
| - | |||
| - | |||
| - | ===== Contact ===== | ||
| - | |||
| - | For questions regarding the connector series, please contact the Dronecode Industrial Community director at <lorenz@px4.io>. | ||
workgroup/connectors/start.txt · Last modified: 2021/02/23 03:04 by Ramon Roche
Page Tools
